preliminary series am el5 -az 5 watt | a c - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052e r 8 1 of 3 north america only features: models single o utput model input voltage (vac/hz) input voltage (vdc) temperature range (oc) output voltage (v) output current max (a) m aximum capacitive load ( f ) efficiency (%) amel5 - 3.3s az 90 - 305 /47 - 440 120 - 430 - 40 to + 8 0 3.3 1. 5 2200 6 6 amel5 - 5s az 90 - 305 /47 - 440 120 - 430 - 40 to +8 0 5 1 1100 69 amel5 - 12s az 90 - 305 /47 - 440 120 - 430 - 40 to +8 0 12 0.42 680 72 amel5 - 15s az 90 - 305 /47 - 440 120 - 430 - 40 to +8 0 15 0.333 330 7 2 amel5 - 24s az 90 - 305 /47 - 440 120 - 430 - 40 to +8 0 24 0.2 1 220 7 4 i nput specifications parameters condit ions typical maximum units current (full load) 115 vac 1 2 0 ma 230 vac 70 ma inrush current <2ms (cold start) 115 vac 1 0 a 230 vac 20 a leakage current 0. 2 ma external fuse slow blow type 1.5 a input dissipation no load <0. 5 w output spe cifications parameters conditions typical maximum units voltage accuracy 2 % line regulation 0. 5 % load regulation 0 - 100% load 0.5 % transient recovery time 200 s transient response deviation 25% load step 2 % of vout m inimum load 0 % ripple & noise 20mhz bandwidth 100 mv p - p *ripple and noise are measured at 20mhz bandwidth by using a 0.1f (m/c) parallel capacitor. isolation specifications parameters conditions typical rated units tested i/o voltage 3sec 3000 vac isolation re sistance >1000 m ? i/o isolation 3 000vac ? rohs compliant ? operating temp: - 40 o c to +8 0 o c ? energy star compliant ? i nput: 90 - 305 vac, 47 - 440hz, or 120 - 430 vdc ? efficiency up to 74% ? over load, over voltage, short circuit protection ? soft start
preliminary series am el5 -az 5 watt | a c - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052e r 8 2 of 3 north america only general specifications parameters conditions typical maximum units switching frequency 66 khz over load protection auto recovery, fold back >116% over voltage protection zener diode clamp short circuit protection auto recovery operating temperature with derating above 50oc refer to the models table above o c storage temperature - 4 0 to +95 o c maximum case temperature 100 o c t emp era ture coefficient 0.02 % / o c humidity non condensing 20 ~ 95 % rh case material plastic resin + fiberglas s (flammability to ul 94v - 0) weight 30 g dimensions ( l x w x h) 2.0 3 x 1. 10 x 0. 70 inches 5 1.5 x 28 x 17.8 mm mtbf > 400 000 hrs (mil - hdbk - 217f, t=+25 o c) note: all specifications in this datasheet are measured at an am bient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. environment approval parameters conditions shock wave form: half sine wave acceleration amplitude: 5gn bump duration: 30 ms number of bumps: 18 (3 in each direction for every axis) converter operation before and after test, body mounted (on chassis) vibrations test mode: sweep sine 10- 100hz, speed 0.05hz/s displacement: 1mm acceleration: 3g 3 loops 30min one cycle, 3h total , every axis tested converter operation before and after test, body mounted (on chassis) safety specifications parameters agency approvals culus, ce , cb pending standards medical electrical equipment iec \ en \ ul 60950 - 1 information technology equip ment en 60950 - 1:2006+a11:2009 emi - conducted and radiated emission en550 22 , class b electrostatic discharge immunity iec 61000 - 4 - 2 rf, electromagnetic field immunity iec 61000 - 4 - 3 electrical fast transient/burst immunity iec 61000 - 4 - 4 surge immu nity iec 61000 - 4 - 5 rf, conducted disturbance immunity iec 61000 - 4 - 6 power frequency magnetic field immunity iec 61000 - 4 - 8 voltage dips, short interruptions immunity iec 61000 - 4 - 11 pin out specifications
preliminary series am el5 -az 5 watt | a c - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052e r 8 3 of 3 north america only dimensions note: 1. datasheets are updated as needed and as such, specifications are subject to change without notice. once printed or downloaded, datasheets are no long er controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications ar e for reference only. 4. all specifications are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary and may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. warranty is in accordance with aimtecs standard terms of sale available at www.aimtec.com. pin single 1 ac input (n) 2 ac input (l) 3 + v output 4 - v output 5 no pin div : 0. 2 ( 5. 08) 5 ? - 0 . 047 ( ? 1 . 2 ) top view 1 2 3 4 5 dimensions : inch ( mm ) case tolerance : 0. 012 ( 0. 30) pin pitch tolerance : 0. 012 ( 0. 30) 1 . 10 ( 2 8 . 00) 0 . 40 ( 10 . 16) 0 . 40 ( 10 . 16) 2 . 03 ( 51 . 50) 1 . 80 ( 45 . 72) 0 . 80 ( 20 . 32) 0 . 11 ( 2 . 89) top view 1 2 3 4 5 17 . 80 ( 0 . 70) 0 . 2 ( 5 . 08 ) ( min ) ? 0 . 04 ( 1 . 00)
|
